Resurrect.IT – HP dc7700 Small Form Factor PC

Back in my lab – sounds great, doesn’t it – ok, it isn’t actually a laboratory, but it is my
working area where I work on computers.  I have worked in a real laboratory though – the Sydney County Council Measurements Laboratory, at the School of Electrical Engineering, UNSW.  We worked in the area of precise electrical measurements, was NATA registered and cooperated on many projects with CSIRO.  Ever actually measured a nanovolt?  I even designed and built a frequency divider with missing pulse detection for a rubidium frequency standard.  Another thing we did was to measure the capacitance of a semiconductor junction in a transistor – never before measured, only theoretical capacitance – and the measurement agreed quite well. This lab is long gone as is the Sydney County Council, but I digress.

Ok – the job at hand, to access stored browser passwords on the machine. One utility I have can access IE 7 & 8 protected storage passwords, but need to know the logon password, as this is used to encrypt the passwords.  The other utility can look for other browser passwords, but needs to run on that machine as that user.  Choices galore! In this case though, the Edwin user did not have a password, and I did not locate any internet explorer stored passwords. So now I need to “resurrect.it“.  Replacing the motherboard is possible, but after doing this, it might also be the power supply – or a combination. I could get a second hand machine on the internet – probably cost $100 plus, is it worth it?

I decided first to have a look at the power supply. After removing it from the machine, I opened it up and had a visual look – I found an electrolytic capacitor that was bulging, a sure sign of over-heating, but checking its ESR (Equivalent Series Resistance) – it wasn’t high. I didn’t have a direct replacement on hand, but I replaced it with one that was close enough but this did not fix the problem. I also removed the cmos battery – a CR2032, while I did more cleaning up. I removed the cpu cooler, took it apart to get rid of the accumulated dust, then checked the cpu, an Intel Core 2 Duo E6300. I cleaned the thermal compound off the cpu and heatsink, then applied Arctic Silver 5 and reinstalled the cpu and heatsink. After putting everything back in, applying power did not give the beeps and this time, the power stayed on. The machine still however failed to boot from the hard disk – but it was certainly working better than before. My diagnostic card that was plugged into the PCI slot did not indicate anything other than that the voltages were nominal.  This often means that the motherboard has failed – but it could be the bios has been corrupted. In any case, continuing on further is not economical – but I could do this later just as a learning process.

I could “resurrect.it” by virtualizing the machine.  Is this like virtual reality, you might be thinking – yes, very similar.  That is what I started doing yesterday. I have currently two VMware servers running, a new ESXi 5.5 server that I am configuring, and an old ESXi 4.0 server that runs my other virtual machines.  The first thing to try is whether or not the disk image that I collected previously would boot directly on VMware – it is unlikely, but is worth a try since it doesn’t take long, but I do need to bring the disk image into VMware first.

Step 1. Create a new virtual machine on esxhost2 (my new ESXi 5.5). The machine is called tdc7700 (for testing). The machine though is empty and I need to populate it.

Step 2. Boot the tdc7700 vm with a Ubuntu cd – once that is running, copy the disk image from the network onto the disk. I use dd again but before doing this I had to mount the network share using the mount -t cifs command.  Ok – done.

Step 3. Modify tdc7700 settings to make the disk independent, and not allow changes to be written.  This is to avoid having to copy the image again if something goes wrong.

Step 4. Power on tdc7700 – I saw the Windows XP screen come up briefly before a blue screen. Ok – thought it might happen.  This is probably because the original machine had a sata disk controller, and now tdc7700 has a scsi disk controller.  It cannot locate the original disk, hence the blue screen.

From here on, I will need to do a P2V conversion – a physical to virtual conversion, where in my case the physical is actually this tdc7700. There are a number of ways to do this, but the best way is to run the VMware offline converter which unfortunately is obsolete, but still usuable.  The converter is smart enough to make changes to windows hardware configurations in order to create a disk image that would run in a virtual environment.

Continuing, then…

Step 5. Boot the tdc7700 vm with a coldclone303 cd. Press the appropriate buttons to get to a target virtual machine called vdc7700 – it wouldn’t work to access esxhost2, strange. Everything is fine until it verifies the destination environment, then stops with an error. My esxhost2 is a newer VMware host and the datastore version is VMFS 5 – maybe this is causing a problem? So tried again, but now going to esxhost1 (my ESXi 4.0) server whose datastore is VMFS 3.  Success – I start the importing of the machine and it took about two hours to run.  Not bad with processing 80GB of disk across the network.

In the meantime, I was able to find a newer version of coldclone being 4.1.1, so when this finished, I tried again with coldclone411 but it still wouldn’t accept a destination of esxhost2, so decided to continue anyway, and create another virtual machine called vtdc7700 as it was time for bed. This time, I elected to minimize the size of the disks for the import process. once it had commenced, I went to bed.

This morning, I checked that the import had finished. Yes, it had – and now, will it work?

Step 6. Power on the new vdc7700. Yes, it boots up – at low resolution anyway. It tries to
update some drivers for changing hardware, that’s ok. I rebooted, then logged in and installed the VMware Tools – this ran, but then the machine hung – not so good, but not too bad.  Reset it and tried again, then successful. Changed the resolution to 1024×768 – much better. It has been resurrected!

Step 7. Run my utility to check for IE passwords – none, what? Check other browser passwords – none either.

I can access the machine in my virtual environment, but a lot of the programs are in Chinese, and I don’t read Chinese. It looks like 360Safe is installed. They are not using Internet Explorer so might be using the 360Safe browser to access email. Anyway, I asked them to come and see me and maybe they can show me how they access their email.

So in the meantime, a bright idea occurred to me – I could convert it so that they could run it on one of their other computers by using VMware Player. Since it is running now on my VMware host, it should be able to run on their computer. I will test this out and come back with a later update.

[PS]  Virtualization is quite good for running old machines where some application is still needed that cannot be moved to newer hardware.  Windows NT was always very picky when it comes to hardware and doesn’t cope well with newer hardware – so is very often moved to a virtual environment like VMware to keep it running. Windows XP on the other hand is much better at this and another alternative could be to put the hard disk into another computer and it will just update hardware drivers, maybe even have to activate again due to too many hardware changes at once – maybe I should do this and get rid of that old computer that is sitting around…

Advertisements

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s